# 2 This is a lever that will allow you
to manually open the latch. As you lift
the lever with your finger tips you will
feel tension due to the stainless
steel spring that operates the latch.
You place fingers here and lift
------------------->
On top you will see a bolt sticking up. This bolt is
on a swivel. If you want to lock the latch in the
open position while in the drivers seat, you would
simply lift the lever and slide the bolt under the
lever. This will hold the latch open
# 1 Raise lever up and slide
bolt  underneath the lever with
finger tips. This will hold latch
open.
Important Note:  #1 and  # 2 is helpful when unhooking from the implement, but is not necessary during
the hooking up process
# 4 Each end of the stabilizer bar has a 90 degree hook. To use the stabilizer bar you would hook each
end into the hole on the end of the pin that holds the Quick Connects onto the drag arm of the 3 point
hitch.
# 5 The stabilizer bar is in two pieces. One piece slides inside the other in order to adjust the distance
between the two drag arms of the three point hitch. Once you get the distance set there is a knob with a
hand grip that you can turn in order to tighten down the stabilizer bar to prevent any slippage in the
adjustment.
Below are the 7 most asked questions by customers when placing their
order.
---->
# 3 A U Bolt fits over and
around  the drag arm and
slips through the bolt
holes as shown on the
bottom  and back of the
quick connect. Once the U
Bolt is tighten up this will
keep the quick connect
straight and level with the
drag arm
---------------------->
----------------------->
# 6. You can hook a category 2 quick connect to a implement with a category 1 hook up, but you would
need to slip a bushing over the category pin on the implement to use as a spacer. The bushing can be
found at Tractor Supply Stores or Tractor Dealer Stores.

# 7 The same would be for the Category 3 quick connect for implements with a Category 1 or 2 hook up.
# 8 The Stabilizer cannot be used when using a PTO driven implement. The stabilizer  would be in the
way of the PTO shaft.
DTN Agricultural news, market reports, world news, U.S. news, local and national weather and weather radar
DTN world, US, market,futures, poltical news headlines
DTN world, US, market, poltical news headlines
DTN market news, early word opening livestock, grain comments, livestock comments, early word opening grains, feeder pig
DTN Ag news, cattle, soybean, Volume and open interest, daily market monitor
DTN Soybean rust report and soyebean rust information
DTN local, national weather radar, farm weather
Fox News national, world and business news
Wells Ag Tractor Canopies for all tractor makes and models
Your name:
Your email address:
Your phone number:
Comments:
For more information or to order place shipping address in the comment box below. You will be invoiced
after your order is shipped. You can paid by check.
You can also call 256-513-2023.  All pricing is current.
Category 1 hitch PIN HOLE SIZE IS     7/8"
Category 2 hitch PIN HOLE SIZE IS    1 1/8"  
Category 3 hitch PIN HOLE SIZE IS    17/16"
TYM
# 9 Not often, but on some tractor models the top center link of the three point hitch can be to short
after installing the quick connects. We have top links that we can provide at our cost for $ 30.00 .
Note: the quick connects will add 3 1/2" to the length of the drag arms of your three point
hitch.
We also have these quick connect combinations
Category 1 quick connect that has a category 2 hook - $ 199.00
Category 2 quick connect that has a category 1 hook - $ 199.00
Category 2 quick connect that has a category 3 hook - $ 265.00
Stabilizer  $ 20.00
Shipping is $ 20.00 for each category with the stabilizer bar.
The ARGnews Group
Super Hay Tarp, tear resistant
# 10 One way of deteriming your three point hitch category size is by measuring the pin hole on the drag arms.
# 11 Lynch Pins are used to keep the pins from sliding out of the quick connect hook. View Lynch Pin
placement in place in this picture 00000000000Click on picture to enlarge